Any unpaid portion not received by the due date will no longer form part of the equal payments plan and interest will accrue on that amount from the day after the date of your next statement at the applicable regular annual rate. Each month during an equal payments plan you are required to pay in full by the due date that month’s equal payments plan instalment. There is no administration fee charged for entering into a special payments plan. However, if we do not receive the full minimum due on a statement within 59 days of the date of that statement, or any event of default (other than a payment default) occurs under your Cardmember Agreement, all special payment plans on your account will terminate and (i) you will then be charged interest on the balances outstanding on such plans at the applicable regular annual rate from the day after the date of your next statement, and (ii) the balances outstanding will form part of the balance due on that statement. Interest does not accrue during the period of the plan. Dealers may sell for less.įinancing available is “Equal payments, no interest” for 24 months (unless otherwise stated) and is only available on request, on approved credit and on purchases of $150 (unless otherwise stated) or more (Gift Cards excluded) made with your Triangle credit card at Canadian Tire, Sport Chek, Mark’s, L’Équipeur, Atmosphere, Sports Rousseau, Hockey Experts, L’Entrepôt du Hockey and participating Sports Experts. **Online prices and sale effective dates may differ from those in-store and may vary by region. ±Was price reflects the last national regular price this product was sold for. The tire producer / manufacturer and Canadian Tire uses this fee to pay for the collection, transportation, and processing of used tires.ĬANADIAN TIRE® and the CANADIAN TIRE Triangle Design are registered trade-marks of Canadian Tire Corporation, Limited. Position strike in line with latch and attach with two flathead screws.△The tire producer / manufacturer of the tires you are buying, and Canadian Tire is responsible for the recycling fee that is included in your invoice. Insert spindle through hole A and attach knobs at each end of spindle.ĩ. Position trim plates on door in line with lock and attach using eight oval-head screws.Ĩ. Insert lock into door and attach with two flathead screws.ħ. Insert lock occasionally to ensure proper depth.Ħ. Chisel out the wood within the lines to a depth of approximately 3/32″. Insert mortise lock into pocket, draw a line around the face plate, and remove lock. Drill four 5/16″ holes as indicated through the door to form slot B.ĥ. Drill one 3/4″ hole on mark A through the door. Chisel out remaining wood to form a pocket in the edge of the door measuring 5/8″ wide by 4-1/8″ long by 3″ deep.Ĥ. Remove template and drill seven 5/8″ diameter holes 3″ into edge of door where C holes were drawn. Be sure the template does not move up or down.ģ. Position vertical line C in center of door thickness and mark holes as shown. Fold template (see insert included) along dotted line and wrap around inside edge of door at a convenient height. Replaces most bit key mortise locks with 2-1/4″ backsetġ. Lock bolt is key activated both inside & outside Proposition 65 Warning Proposition 65 Warning Finishīolt reversible to left and right handed door As needed, use chisel to cut door jamb so that strike is flush with door jamb. Remove strike plate and drill 1/8″ pilot holes.Ħ. Attache lock to door by inserting screws through lock into door.ĥ. Plack lock on door so that connecting bar enters slot. Cut off connecting bar so that it projects 3/8″ beyond inside of door.Ĥ. Cut screws to proper length relative to door thickness.ģ. Connect back plate to cylinder with two connecting screws. Insert cylinder and ring from he outside of door and place back plate on inside of door. At desired height bore the hole for the cylinder 1-1/4″ diameter, with center at a distance of 2-3/8″ from edge of door.Ģ. Latch hold-back (prevents locking yourself out)ġ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |